Author Topic: I have a problem  (Read 4954 times)

Offline GCNinja

  • *
  • Posts: 2
  • Karma: +0/-0
    • View Profile
on: July 04, 2008, 04:38:51 PM
ok, seriously, im about to cry, ive worked on this for about three days altogether and NOTHING.  I'm using http://www.terracode.com/IR_Pen/DIY_IR_Pen.html as a guide and bought ALL the parts, using their parts #.  I have four of each and none work.  I know that the longer is the pos and shorter is the neg, so i got that but still, nothing.  I dont need a resistor but i didnt solder, i just used the rubber boot to hold them, and wrapped the wire around the switch, does this matter?
I used a webcam to test because it detects my TV remote IR, does THIS matter? and finally, ill try to get pics up, ASAP. 

ANY suggestions will help, THANK YOU



Offline Francisco

  • *
  • Posts: 48
  • Karma: +1/-0
    • View Profile
    • http://clinik.net/wiimote/
Reply #1 on: July 04, 2008, 08:12:34 PM
It seems everythngs ok...
Check my IR Pen #2 http://clinik.net/wiimote/wiimote_info_my_pen_2.php just in case...
Perhaps you have some ideia...


Offline UndCon

  • Support Admin
  • *
  • Posts: 566
  • Karma: +11/-3
    • View Profile
    • UndCon
Reply #2 on: July 05, 2008, 03:03:14 AM
IM not sure here but you say you tested with the webcam - did you see the light go on/off from the IRpen ?

just 1 thing to make sure works...

webcam, cellphonecams, digicams all works just fine to verify your IR-LED turns on and off when you press your buttons

//UndCon



Offline benpaddlejones

  • Support Admin
  • *
  • Posts: 1178
  • Karma: +49/-0
    • View Profile
    • Inter.Connect.Ed
Reply #3 on: July 05, 2008, 08:21:20 AM
GCNinja

First:
Read - http://www.wiimoteproject.com/ir-pens/electronics-101-sharing-my-mistakes-updated-t834.0.html Make sure you have applied all the lessons.

Second:
Solder!  ;D
The low current is easily lost through a poor connection. A soldering Iron cost a few dollars from any electronics store.
Watch this to learn how to:
[youtube]BLfXXRfRIzY[/youtube]

Goodluck

Benpaddlejones  :D


See my full profile and links on my Google Profile: http://www.google.com/profiles/benpaddlejones


Offline GCNinja

  • *
  • Posts: 2
  • Karma: +0/-0
    • View Profile
Reply #4 on: July 08, 2008, 07:18:19 PM
good news and bad news!
Good news: I got it working! bad news, it was w two AA and nit burned both me and the bulb....so ya....i guess i bought the wrong LED though i used the given product code.   
Bad News: it burnt out.   I have one more and i hope i can figure out WTF...

i found it it used AA cuz i was soldering w a ColdHeat (which if you have one, you know they suck) and it came on, so i used two AA like the CH does and it burnt me and the bulb.

any suggestions? one more try....

i hope i dont have to order any more of these LEd, i gotta ship them cuz the nearest place that sells then IE radiocrap is 80miles away



Offline benpaddlejones

  • Support Admin
  • *
  • Posts: 1178
  • Karma: +49/-0
    • View Profile
    • Inter.Connect.Ed
Reply #5 on: July 08, 2008, 11:14:18 PM
Ninja

I have already given you the solution to this problem >:(:

GCNinja

First:
Read - http://www.wiimoteproject.com/ir-pens/electronics-101-sharing-my-mistakes-updated-t834.0.html Make sure you have applied all the lessons.


You can take a horse to water but you can't make it Drink!  ;D

Benpaddlejones


See my full profile and links on my Google Profile: http://www.google.com/profiles/benpaddlejones