Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - IACG

Pages: 1
1
Bluetooth & Connectivity Help Center / Re: connecting second Wiimote
« on: June 02, 2009, 06:23:51 PM »
I seem to have figured it out.  If I right click on each of the wiimotes and choose disable before I start the procedure, then I go through the steps to connect.

1.  Blue Tooth Setup Wizard, then choose I want to find a specific blue tooth device and configure how this computer will use it's services.
2.  Press and hold the 1 and 2 buttons on the remote until step 6.
3.  Select the device and click Next.
4.  Click Skip when asked to pair.
5.  Check off the wiimote in the "Select service..." anc click Finish.
6.  The computer makes a da-ding sound and then I let go of the buttons.  About 6 seconds later the green connected symbol shows up

Repeat for other Wiimote.

If you don't disable the wiimotes it will just flash connected then go to disconnected.

Hope this helps someone else out.

IACG




2
Bluetooth & Connectivity Help Center / Re: connecting second Wiimote
« on: June 02, 2009, 05:45:23 PM »
Thanks for the replies.  Sorry it took so long for me to respond back, work has been far too busy!

I'm using Broadcom Corporation Version 2.1.207.297 (HP Integrated Module with Bluetooth 2.0 Wireless Technology)

Thanks for any help you can offer.  IACG

3
Bluetooth & Connectivity Help Center / connecting second Wiimote
« on: May 27, 2009, 04:22:17 PM »
I'm having trouble connecting a second wiimote to my HP Laptop.  I'm using the built in Bluetooth wireless.  I've been following the instructions for the widcom bluetooth stack.  I have no trouble connecting the first remote, but the second connection will only flash on for a second.  I click on the icon for the wiimote that is not connected and then click on bluetooth setup wizard.  The wiimote is found and I check it off in the screen that appears.  At this point I can see that wiimote icon change to connected for a second.  But when I click finish, it does not connect.

I'm Running Windows XP Prof. on an HP Compaq 6715b.  The BT uses a Broadcom Driver.


A couple of things I have done:
I renamed the two wiimotes to "Nintendo RVL-CNT-01 LEFT" and "Nintendo RVL-CNT-01 RIGHT"

I can connect either remote, which ever I try first works fine, just not the second.

I downloaded Blue Soleil and I was able to connect both at the same time, but it was a trial thing and could only be used for a limited time and so I have uninstalled it.

Any help would be greatly appreciated!

4
General Discussion / Trouble connecting second wiimote
« on: May 22, 2009, 09:05:51 AM »
I'm having trouble connecting a second wiimote to my HP Laptop.  I'm using the built in Bluetooth wireless.  I've been following the instructions for the widcom bluetooth stack.  I have no trouble connecting the first remote, but the second connection will only flash on for a second.  I click on the icon for the wiimote that is not connected and then click on bluetooth setup wizard.  The wiimote is found and I check it off in the screen that appears.  At this point I can see that wiimote icon change to connected for a second.  But when I click finish, it does not connect.

A couple of things I have done:
I renamed the two wiimotes to "Nintendo RVL-CNT-01 LEFT" and "Nintendo RVL-CNT-01 RIGHT"

I can connect either remote, which ever I try first works fine, just not the second.

I downloaded Blue Soleil and I was able to connect both at the same time, but it was a trial thing and could only be used for a limited time

Any help would be greatly appreciated!

Pages: 1